Close

Activity Stream

Filter
Sort By Time Show
Recent Recent Popular Popular Anytime Anytime Last 24 Hours Last 24 Hours Last 7 Days Last 7 Days Last 30 Days Last 30 Days All All Photos Photos Forum Forums Articles Articles
  • Iateone2's Avatar
    1 Day Ago
    Thanks for the start. Will definitely static test.
    2 replies | 18 view(s)
  • Redzwulf's Avatar
    1 Day Ago
    Here you go. Please note that this is provided to get you close and that you should do your own static test.
    2 replies | 18 view(s)
  • Iateone2's Avatar
    1 Day Ago
    Looking for guide spacing recommendations for an immortal spey IMMF1266-4 to be used for a center pin rod. Haven't been able to find anything on the...
    2 replies | 18 view(s)
  • Redzwulf's Avatar
    4 Days Ago
    Redzwulf replied to a thread Centerpin Moocher in Rod Building
    Laid out the guides and did a test wrap on a piece of doweling. Next comes the static testing and guide train.
    1 replies | 37 view(s)
  • Redzwulf's Avatar
    1 Week Ago
    Redzwulf replied to a thread Reel Seat Sizes in Rod Building
    Mfgs will have the reel seat specs listed. If you have a look in the Batson catalog at http://www.batsonenterprises.com/Catalogs/2017Catalog/ you...
    1 replies | 65 view(s)
  • peteskeet's Avatar
    1 Week Ago
    peteskeet replied to a thread NFC guide spacing in Rod Building
    Im looking at an ALPs MVT toray trigger. The grip will most likely be go a 9 carbontex grip, but I might be looking to go for a little longer....
    8 replies | 1659 view(s)
  • Redzwulf's Avatar
    1 Week Ago
    Redzwulf replied to a thread NFC guide spacing in Rod Building
    Tip diameters are also on their website. As far as reel seats, you want to pick one that fits your reel, fits your hand, and is appropriately...
    8 replies | 1659 view(s)
  • peteskeet's Avatar
    1 Week Ago
    peteskeet replied to a thread NFC guide spacing in Rod Building
    What about an MB 709-1 casting? I saw the guide specs on the website, but I was wondering if you had any other info such as tip diameter, reel seat...
    8 replies | 1659 view(s)
  • peteskeet's Avatar
    1 Week Ago
    peteskeet started a thread Reel Seat Sizes in Rod Building
    Hi Guys, First time rod builder here, and I couldn't find a clear answer on finding the reel seat ID size for your rod. Is this something that...
    1 replies | 65 view(s)
  • Redzwulf's Avatar
    1 Week Ago
    Newest project that is work in progress... North Fork Composites SA1064-2 (IM) with 9" Winn rear grip, Alps centralock reel seat, and 18" Winn...
    1 replies | 37 view(s)
  • Redzwulf's Avatar
    1 Week Ago
    Redzwulf replied to a thread New Grips in Rod Building
    There was talk that at some point they would be available for sale but when that is, I have no clue. Regards, Eric
    4 replies | 376 view(s)
  • peteskeet's Avatar
    1 Week Ago
    peteskeet replied to a thread New Grips in Rod Building
    Thanks for the reply. Nice find!
    4 replies | 376 view(s)
  • Redzwulf's Avatar
    1 Week Ago
    Redzwulf replied to a thread New Grips in Rod Building
    These are the same grips (Black Widow) made by North Fork Composites and used on Edge rods. They are currently not available for sale to the...
    4 replies | 376 view(s)
  • peteskeet's Avatar
    1 Week Ago
    peteskeet replied to a thread New Grips in Rod Building
    Where can these be purchased? These look similar to the ones used on the black widow series by Edge.
    4 replies | 376 view(s)
  • Eric Kol's Avatar
    2 Weeks Ago
    Eric Kol replied to a thread Rx8 xst1324f in General Discussion
    Thank you for the speedy reply. I'm building this as a spin rod. I had a similar rod stolen this summer so I'm finally getting around to replacing...
    2 replies | 95 view(s)
  • Redzwulf's Avatar
    2 Weeks Ago
    Redzwulf replied to a thread Rx8 xst1324f in General Discussion
    Hello Eric, First off, welcome to the forums. Your build is pretty interesting...are you planning on a cast or spin rod? I've included both...
    2 replies | 95 view(s)
  • Eric Kol's Avatar
    2 Weeks Ago
    Hey all. New to the forum. Looking for guide spacing chart and any other build opinions and components ideas for the xst1324f blank. Thanks, eric
    2 replies | 95 view(s)
No More Results